Svenska ElektronikForumet

Kod: Markera allt

int switchPin = 8;
int out1 = 1;
int out2 = 2;
int trigger1 = 1;
int trigger2 = 3;
int pull = 0;
long Timer1 = 0;
long Timer2 = 0;
long interval = 1000;
long time = 0;

boolean lastButton = LOW;
boolean currentButton = LOW;



void setup()
{
  pinMode(switchPin, INPUT);
  pinMode(out1, OUTPUT);
  pinMode(out2, OUTPUT);

}

boolean debounce(boolean last)
{
  boolean current = digitalRead(switchPin);
  if (last != current)
  {
    delay(5);
    current = digitalRead(switchPin);
  }
  return current;
}

void loop()
{
  time = millis();
  currentButton = debounce(lastButton);
  if (lastButton == LOW && currentButton == HIGH)
  {
    pull = pull + 1;
  }
  lastButton = currentButton;

  if (pull == 4) pull = 0;


  if (pull == trigger1)
  {
    Timer1 = millis();
    digitalWrite(out1, LOW);
    pull = pull + 1;
  }
  if (time - Timer1 >= interval)
  {
    digitalWrite(out1, HIGH);
  }

  if (pull == trigger2)
  {
    Timer2 = millis();
    digitalWrite(out2, LOW);
    pull = pull + 1;
  }
  if (time - Timer2 >= interval)
  {
    digitalWrite(out2, HIGH);
  }
}

Kod: Markera allt

#include <RCSwitch.h>

RCSwitch mySwitch = RCSwitch();
int switchPin1 = 8;
int buttonState;             // the current reading from the input pin
int lastButtonState = LOW;   // the previous reading from the input pin
long lastDebounceTime = 0;  // the last time the output pin was toggled
long debounceDelay = 50;    // the debounce time; increase if the output flickers

void setup() {
 pinMode(switchPin1, INPUT);

  Serial.begin(1200);
  
  // Transmitter is connected to Arduino Pin #10  
  mySwitch.enableTransmit(10);

  // Optional set pulse length.
  // mySwitch.setPulseLength(320);
  
  // Optional set protocol (default is 1, will work for most outlets)
  // mySwitch.setProtocol(2);
  
  // Optional set number of transmission repetitions.
  // mySwitch.setRepeatTransmit(15);
  
}

void loop() 
{
  // read the state of the switch into a local variable:
  int reading = digitalRead(switchPin1);

  // If the switch changed, due to noise or pressing:
  if (reading != lastButtonState) {
    // reset the debouncing timer
    lastDebounceTime = millis();
  }

  if ((millis() - lastDebounceTime) > debounceDelay) {
    // whatever the reading is at, it's been there for longer
    // than the debounce delay, so take it as the actual current state:

    // if the button state has changed:
    if (reading != buttonState) {
      buttonState = reading;

      if (buttonState == HIGH)
      {
        // Send!
        mySwitch.send(1337, 24);
      }
    }
  }

  // save the reading.  Next time through the loop,
  // it'll be the lastButtonState:
  lastButtonState = reading;
}

Kod: Markera allt

#include <RCSwitch.h>

RCSwitch mySwitch = RCSwitch();

int out3 = 3;
int out4 = 4;
int out5 = 5;
int out6 = 6;
int out7 = 7;
int trigger3 = 1337;
int trigger4 = 7;
int trigger5 = 9;
int trigger6 = 11;
int trigger7 = 13;
int pull = 0;
long Timer3 = 0;
long Timer4 = 0;
long Timer5 = 0;
long Timer6 = 0;
long Timer7 = 0;
long interval = 1000;
long time = 0;

boolean lastButton = LOW;
boolean currentButton = LOW;



void setup()
{
  Serial.begin(9600);
  mySwitch.enableReceive(0);  // Receiver on inerrupt 0 => that is pin #2
  pinMode(out3, OUTPUT);
  pinMode(out4, OUTPUT);
  pinMode(out5, OUTPUT);
  pinMode(out6, OUTPUT);
  pinMode(out7, OUTPUT);

}

  void loop()
  {
    time = millis();

    if (mySwitch.available()) {

      int value = mySwitch.getReceivedValue();
    }
    if (mySwitch.getReceivedValue()  == trigger3)
    {
      Timer3 = millis();
      digitalWrite(out3, LOW);
    }
    if (time - Timer3 >= interval)
    {
      digitalWrite(out3, HIGH);
    }
    if (mySwitch.getReceivedValue()  == trigger4)
    {
      Timer4 = millis();
      digitalWrite(out4, LOW);
    }
    if (time - Timer4 >= interval)
    {
      digitalWrite(out4, HIGH);
    }
  }